Skip to main content

KerfDoors

KERF

KerfDoors

KERF

Build one-piece routed cabinet doors from a groove profile, fill or import an order, nest it onto sheets, and get Manufacture setups plus one G-code file per tool, ready for the machine.

$20.00/month

Kerf Doors builds routed MDF cabinet doors inside Autodesk® Fusion® and takes them all the way to the G-code files your machine runs.

ONE PROFILE, ANY DOOR Pick a groove design — a bead and cove, a small bead and ogre, a recessed shaker, a V-groove, a bull nose over a cove — type a width and a length, and Kerf Doors sweeps the groove around the door, recesses the center panel when the design calls for it, and chamfers the outer edge. 71 profiles ship with the add-in: 13 reproduce the standard one-piece MDF door profiles the trade cuts every day, 48 more are the deeper frame-and-panel combinations, and every one is sized for 18 mm MDF and for cutters a shop already owns.

A WHOLE ORDER, FILLED IN OR IMPORTED Switch to Batch order and fill a table inside the dialog: one row per door size, with the design, the chamfer and the CAM template picked from lists rather than typed. Or load a CSV or Excel order you already have. Orders are saved under their own name as plain CSV, so they reopen, edit and still open in Excel.

NESTED LIKE A SHEET GOES ON THE MACHINE Doors are nested onto your sheet size with your margin and gap, rotated 90° where that saves material, and never mixed across thicknesses. Each sheet becomes its own component holding a see-through board body and its doors, named and grouped in the timeline. That board is the stock of the sheet's Manufacture setup, and you choose which corner of it the machine zero sits on.

CAM THAT FOLLOWS THE DOOR Automatic mode plans a 2D-first recipe from the profile itself: pockets for the floors, a radius or point-cutting round over for beads, ball end mills for coves, a chamfer mill for bevels, wall and junction traces, and a 3D pass only where no 2D cutter fits. Before a tool path exists, a section check sweeps the planned cutters across the design and reports anything they would leave behind. The cutout comes last, as it must: where two doors sit exactly one cutter apart a single common-line pass cuts both edges at once, holding tabs sit near every corner, and the release pass touches only the tabs, so a freed door is never machined again.

YOUR RECIPE, REUSED Tune a setup once, click Save CAM Template, and the operations — tools, feeds, strategies and what every selection meant on the door — are captured as a template that re-applies to any door size of that design, on its own or by name in an order.

G-CODE, ONE TOOL PER FILE Post from the batch or from the Manufacture workspace: every setup becomes one G-code file per tool, in machining order, with the cutout and the tab release in files of their own. Files are named by sheet, run order, tool and stage, each is an NC program in the browser you can simulate, and a run sheet lists them in the order the operator runs them. One tool per file is exactly what a Personal Use licence posts.

YOUR PROFILES, YOUR CUTTERS Draw a new groove cross-section in a guide sketch, save it, and watch the finished door rebuild live while the dialog is open. The add-in checks the shape, works out whether the center panel is recessed and writes the machining recipe next to the profile. Your profiles, orders and templates live in your Documents folder and appear in every list beside the built-in set.

MADE FOR THE SHOP Millimetres throughout, sheet sizes and gaps you choose, a full log and a short summary of every run, no internet needed for the work itself.
Kerf Doors is the sibling of Kerf, the parametric casework add-in for Fusion, and shares its brand and support. Draw the profile. Cut the doors.
Autodesk and Fusion are trademarks of the Autodesk group of companies. Kerf is not affiliated with Autodesk.

Details

Frequently asked questions (FAQs)

What you need.Fusion with the Manufacture workspace, and a tool library holding metric end mills. The automatic recipes expect flat end mills (a roughing size, 8 mm and 4 mm), ball end mills for coves, a 45 degree chamfer mill, and for beads either a radius cutter or an Amana-style point-cutting round over; Kerf Doors adds the round overs and a tapered ball to the document itself when your libraries do not have them. Cutters are matched on the diameter, corner radius, angle andflute lengthyour library states, so an entry with the wrong flute length makes the planner pass a cutter over. Every run says which cutter it chose for each feature and why, in Documents/KerfDoors_Logs.

Units and files. Millimetres everywhere in the dialogs and the order file; Fusion's own centimeters never surface. Groove profiles are DXF cross-sections, orders and saved orders are plain CSV, CAM templates are JSON, all in Documents/KerfDoors_Settings, so they can be copied between machines or kept in version control. Posted G-code goes to Downloads/KerfDoors.

The profile set. 71 groove profiles ship with the add-in: 13 reproduce the standard one-piece MDF door profiles sold by the trade (bead and cove, small bead with ogre or bevel, beaded round, recessed and stepped shaker, square cove, ogre bead, V-groove, 30 degree slant), 48 are the deeper 3/8 in frame-and-panel combinations, and 10 are hand-drawn designs. Each one lists its size, its center panel and the cutters it needs in profiles/README.md inside the add-in folder.

Offline. Only the App Store licence check uses the network, once per Fusion session; everything else works with no connection. See the privacy policy for exactly what is sent.

A profile whose arc radius matches no cutter in your libraries is finished with a 3D scallop pass instead of a single 2D trace. It is accurate but far slower, and the run log names the cutter or the radius that would cut it in one pass.

Cutter choice trusts your tool library: if an entry understates its flute length, Kerf Doors refuses that cutter for a tall feature and falls back to the 3D pass. Correct the entry and it is used again.

A Fusion Personal Use licence posts one tool per NC program and converts rapid moves to feed moves in the output. Kerf Doors posts one file per tool for that reason; the feed-move conversion is Autodesk's and cannot be worked around from an add-in.

Reported issues and fixes: email support@kerf360.com.

Email support@kerf360.com. Please include the Kerf Doors version, your Fusion version and operating system, what you did, and the run summary from Documents/KerfDoors_Logs if there is one. The built-in help (press F1 on any Kerf Doors command) and kerf360.com cover the order table, custom profiles, CAM templates and posting G-code.

Found an issue?

Report a problem