Skip to main content

Ball Bearing Generator (ISO 15)

Stern Didactic GmbH

Ball Bearing Generator (ISO 15)

Stern Didactic GmbH

Place deep groove ball bearings (ISO 15 / DIN 625-1) on a shaft or in a housing with one click: 290 sizes, open/2Z/2RS, DIN 5418 shoulder checks, fit hints. Own component, editable later.

$15.00

Ball Bearing Generator places single-row deep groove ball bearings directly at shaft or housing shoulders — with abutment checks, as a separate component for the bill of materials.

Pick an edge — that's it

Click a circular edge at a shaft shoulder (bearing on the shaft) or a bore shoulder (bearing in the housing): the add-in detects the shaft or bore, seat diameter, shoulder diameter, fillet or chamfer, and seat length. The bearing is always aligned with the planar shoulder — even if the edge has a fillet or chamfer.

290 sizes per ISO 15 / DIN 625-1

Series 618, 619, 160, 60, 62, 63, 64, plus the wide 2RS series 622/623, bore diameter d = 1 to 200 mm, including intermediate sizes /22, /28, /32 and miniature bearings (with the common dealer names 681…699). The add-in suggests bearings matching the seat diameter, series 62 first; "Show all sizes" opens the full catalog.

Variant and representation

  • Open, 2Z/ZZ (shields), or 2RS (seals)

  • Detailed (inner ring, outer ring, balls, shields/seals) or simplified (envelope body for large assemblies)

  • Steel and rubber materials for display and mass

  • Offset from the shoulder and "Other side" at step edges

Checks per DIN 5418

The result field lists the abutment dimensions (shaft shoulder da min, housing shoulder Da max, fillet ra max), the measured shoulder, and a fit recommendation (shaft js5 up to d = 10 mm, otherwise j5/k5/m5; housing H7; note for floating bearings). Warnings appear for a shoulder that is too low or too high, a fillet that is too large, a seat that is too short, or a seat diameter that does not match.

Modeled for drawings

  • The ball count is always even, and one ball lies in a principal model plane — every axial section through that plane shows two opposite balls, as drawing standards require. If the real ball count is odd, the result field states the original value.

  • The balls touch the inner and outer raceways exactly — no gap and no interference.

Own component, editable later

The bearing is created as its own component (e.g., "Deep groove ball bearing 6205-2RS") and appears as ONE item in the timeline. Double-click it (or "Edit Feature") to change the size, variant, and representation — the position is kept, and the checks run again.

Who is it for?

Mechanical design engineers, gearbox and fixture design, and training — wherever bearing seats need to be added to the model quickly, consistently, and with checks.

Note

Main dimensions d × D × B and r_s per ISO 15 / DIN 625-1, checked against the catalogs of five manufacturers. The internal geometry (ball diameter, ball count, raceways) is a representation, not manufacturer data. Take load ratings, speeds, and service life from the manufacturer catalog; responsibility remains with the engineer.

Details

Frequently asked questions (FAQs)

Standards/data basis: Main dimensions d × D × B and chamfer r_s min per ISO 15 / DIN 625-1 (dimension series 18, 19, 00, 10, 02, 03, 04, plus the wide 2RS series 622/623), fully checked on 07.10.2026 against Timken, Koyo, NSK, NTN, and Schaeffler data (no incorrect values found; designation 602 instead of 60/2; 62213, 62311, and 62312 added); single-source entries and series 64 are flagged in the result field. Abutment dimensions per DIN 5418 logic (da min = d + 2·h min, Da max = D − 2·h min), table checked against Schaeffler/NSK/NTN/Koyo and corrected in three values. Internal geometry (ball diameter, ball count, raceways, lands) is a representation — typical values or approximations, not manufacturer data. No load ratings, speeds, or service-life calculations. Fit recommendations are guideline values.

Privacy: The app works fully offline, sends no data, and requires no registration.

Compatibility: Fusion (Windows and macOS), parametric design (timeline). In direct modeling mode (no timeline), the bearing is created without the single-item wrapper and cannot be edited by double-clicking.

Also included in the Normtoolbox (nine tools in one add-in); both can be installed side by side, and bearings remain editable with either.

Roadmap: Create the housing bore/shaft shoulder, apply the fit directly, and support angular contact, self-aligning, and cylindrical roller bearings. Feature requests are welcome at support@sterndidactic.com.

No reproduction of standard texts; the current original standard is binding. No affiliation with DIN e.V. or the named manufacturers; DIN is a trademark of DIN e.V.

  • The edit dialog intentionally has no live preview or edge selection (for stability); the position is kept, and the size, variant, and representation are rebuilt when clicking OK.

  • Editing rebuilds the component content — joints or dimensions referencing old bearing faces may need to be reapplied.

  • In direct modeling mode (no timeline), there is no single-item wrapper.

  • The internal geometry is a representation; series 64 and a few sizes are flagged as having limited data sources.

  • No load ratings or speeds are provided — use the manufacturer catalog.

Email support: support@sterndidactic.com — we usually reply within 24–48 hours on business days, in English or German.

To help us assist you quickly, please include: Fusion version (Help → About), operating system (Windows/macOS), app version, the steps you took, and, if possible, a screenshot of the dialog or message.

Publisher: Stern Didactic GmbH, Germany — www.sterndidactic.com

Found an issue?

Report a problem