Skip to main content

Auto Join Pro

CYF BIM Studio

Auto Join Pro

CYF BIM Studio

Batch join geometry and find clashes across a whole view or model — and decide which category cuts which, so the result is consistent everywhere.

Free

Auto Join Pro joins geometry and finds clashes in Autodesk® Revit® models a whole batch at a time. Choose a scope, choose the categories, set the order they are processed in, and run.

SCOPE

  • Project — every element in the model.
  • Active View — everything visible in the current view, which is the practical way to work storey by storey.
  • Selection — only the elements you have picked.

TWO MODES, ONE SETUP

  • Join — joins intersecting elements across the categories you chose.
  • Clash Check — reports where elements overlap, without modifying the model.

Both modes share the same scope and category settings, so you can check, join, then check again.

YOU CONTROL THE ORDER

Revit has its own idea of which element cuts which, and for most category pairs that idea is fixed: floors cut walls, floors cut beams, walls cut columns. For quantity take-off that order is often the wrong way round. Where Revit has no fixed rule, the outcome falls back to whichever join you happened to make first, so working by hand across a model means the convention drifts — one corner ends up different from the next.

Auto Join Pro turns the order into a setting. Move the categories you want into the priority list and rank them high to low. Every join the tool creates follows that order: whatever sits higher cuts whatever sits lower. The default reads Structural Columns, Structural Framing, Structural Foundations, Floors, Walls.

Joins that already exist are left exactly as they are. The tool only adds joins — it never removes one, and never changes the direction of a join you or Revit already made.

That consistency, not just the speed, is the reason to use it.

CATEGORIES

Join works on Structural Columns, Architectural Columns, Structural Framing, Structural Foundations, Floors, Walls and Roofs.

Clash Check adds Stairs, Toposolids, Ceilings, Generic Models and Slab Edges. Those five are checked for overlaps but never joined, because their join behaviour is unreliable or depends entirely on how a family was built. The list changes automatically when you switch modes.

CONCRETE, NOT STEEL

Steel members are skipped in Join mode. Joining them changes nothing: Revit records the join but cuts no geometry, and Revit's own Join Geometry command does not offer steel either. Steel belongs in Revit's Steel tab. Anything not marked as steel is processed normally.

WHEN REVIT REFUSES A CHANGE

Occasionally a join would invalidate something that references the geometry, most often a dimension attached to a face the join consumes. The tool skips that operation, carries on, and at the end reports how many were skipped, shows Revit's reason, and selects the blocked elements and the cause. Nothing is ever deleted.

The whole run is a single undo step — one Ctrl+Z restores the model. Before a large batch the tool asks you to confirm, so you can save first.

WHY THIS MATTERS

Overlapping solids get counted twice in your schedules, and on a level with hundreds of elements, joining every intersection by hand takes hours and still misses some.

PRICE

Free. No trial period, no feature limits, no account required. It runs entirely on your machine, collects nothing, and never connects to the internet.

WHO IT IS FOR

Built by a licensed civil engineer who prepares quantity take-offs. If someone downstream reads numbers off your schedules, this is aimed at you.

BEFORE YOU RUN IT

Joining changes how Revit divides volume between elements, so your schedule quantities will change after a batch join. That is the point of the tool, but run it on a copy first and compare the numbers. See the General Usage Instructions.

Autodesk and Revit are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries.

A full run: Clash Check, Join in priority order, then Clash Check again to confirm.

Details

Frequently asked questions (FAQs)

"No changes" on a model where you can see intersections. The tool joins elements whose solids genuinely overlap. Elements that only share a face have no overlapping volume to resolve, and elements that are already joined are left as they are — the tool does not re-arbitrate existing joins.

Steel members are not joined. Joining steel has no effect on the geometry in Revit, and Revit's own Join Geometry command does not accept steel either. Steel is handled through Revit's Steel tab.

Revit does not respond while a batch runs, and on a large model this can take a while. The tool asks you to confirm before a large batch so you can save first or run a smaller scope.

Revit occasionally refuses a join, usually because it would invalidate a dimension attached to a face the join removes. Those operations are skipped and reported when the run finishes. Nothing is ever deleted.

Support is provided by e-mail.

Contact: cyfang.studio@gmail.com

We are based in Taiwan (UTC+8) and will get back to you as soon as we can.

  • When reporting a problem, please include:
  • Your Revit version and build number (Revit > Help > About)
  • The version of Auto Join Pro you are using
  • What you had selected, and what you expected to happen
  • The exact wording of any error message, or a screenshot

Please do not send project files containing confidential or client information. A cut-down sample file that reproduces the problem is usually more useful than the full project.

Found an issue?

Report a problem